TrueCan Industrial Technologies Inc.
Aerial view of a large oil processing facility in Alberta with towers, pipe racks and storage tanks
Eclipse Magnetics Authorized Distributor · Global Distribution

Black powder contamination is wearing out your plant. Take it out of circulation.

TrueCan supplies Eclipse Magnetics filtration for oil & gas and industrial operations — removing abrasive contamination before it damages pumps, valves, seals and heat exchangers, plugs lines, and forces unplanned downtime.

Protect the assetLess abrasive wear on pumps, valves, seals and exchangers.
Increase productionFewer blockages, pressure drops and unplanned outages.
Decrease OPEXFewer change-outs, less disposal, longer equipment life.

Share what you know; technical details are optionalNo obligationWe'll tell you honestly if it's not a fit

The problem

What black powder does inside a running system

Black powder is abrasive contamination that forms as steel corrodes and erodes: iron oxide and magnetite, mixed with non-magnetic material such as silica, sand, salts and process fines. It is small and hard — much of it finer than the pores of conventional filters — so it keeps circulating and keeps doing damage. It appears in hydrocarbon and gas systems, produced water, and other industrial fluid circuits alike.

  • Accelerated wearAbrasive particles act like grinding paste in pumps, valves, seals, bearings and tight clearances.
  • Rising maintenance costPlugged strainers and cartridges, frequent change-outs, and the labour and disposal that go with them.
  • Unplanned downtimeBlockages and pressure drops build until the intervention is an outage, not a planned job.
  • Shorter asset life, lower qualityContamination degrades internal components and is carried downstream into the product.
Aerial view of an oil sands processing facility in Alberta beside a river, with storage tanks and processing units
Every pump, valve and exchanger in a facility like this is exposed to whatever the fluid moving through the plant is carrying.

How it works

Not just magnetic: how capture works

A high-intensity magnetic core sits directly in the flow, and contamination is held on it until cleaning.

01

Magnetic attraction

Ferrous particles — iron, iron oxide and magnetite — are drawn to the magnetic core and held there until cleaning. Eclipse Magnetics' filtration brochure documents its systems removing ferrous particles including submicron particles (below one micron) — fine contamination that can pass through existing filtration.

02

The corral effect

As ferrous particles build on the magnets, they form a growing matrix that physically intercepts and traps non-ferrous particles travelling with them — so part of the non-magnetic fraction is held in the captured material rather than passing through.

03

Static charge

As particles collide in the flowing fluid, static charge can cause non-magnetic particles to be attracted to and retained with the captured material. This is one reason non-magnetic contamination is found in what is cleaned off a unit.

Capability is not a guaranteed efficiency. Capture can occur as described above — it is not a promise that every particle is removed on a single pass in every system. A pilot measures the result on your own fluid.

Captured contamination is cleaned off the rods in minutes at planned maintenance. The core is reused — no disposable cartridges.

A magnetic filtration core standing on a workshop bench, its lower half completely coated in a thick, spiky layer of black ferrous contamination captured from the fluid
What captured contamination looks like: a magnetic core after service, coated in the fine black ferrous material it pulled out of circulation. Photo: Eclipse Magnetics manufacturer example.

This is what comes off the core

The black, spiky coating on this core is fine ferrous contamination — the same kind of abrasive material that otherwise keeps circulating through pumps, valves and seals. Held on the magnets, it stands up in dense spikes along the magnetic field lines until the core is lifted out and cleaned.

This photograph is from an Eclipse Magnetics installation in EDM drilling and heat-treatment service, shown here as a manufacturer example of captured contamination — not an oil & gas installation. On a TrueCan pilot, what comes off your core is photographed and weighed the same way, so you can see exactly what was in your fluid. See the Eclipse case study behind this photo →

Why magnets, not just finer filters?

Barrier filters only catch what is larger than their pores — and the most damaging black powder is often smaller than that. Finer filters also plug faster, add pressure drop, and become a recurring consumable cost.

Magnetic filtration captures fine ferrous contamination that may pass through existing filtration, and holds a large volume of it without the same pressure-drop penalty. Fitted ahead of existing filters, it can reduce the load on downstream filters — so cartridges and media last longer.

Flagship product

MagStream logo — MagStream Magnetic Filtration by TrueCan Industrial Technologies

MagStream — TrueCan's flagship magnetic filtration

MagStream is the flagship model at the centre of TrueCan's range, encompassing upstream, midstream and downstream applications. The application decides the configuration — kept separate below, because the duty is different in each.

Cleaning options: Automatic cleaning versions are available, and pneumatic versions as well.

MagStream magnetic filtration unit — black inline body with stainless flanges, blue butterfly valves and the larger drain valve assembly below, labelled MAGSTREAM Magnetic Filtration by TrueCan Industrial Technologies
The MagStream unit in full — stainless flanges, blue butterfly valves and the larger red-handled drain valve assembly below the body. Branding concept image, as labelled on the image — not a photograph of an installed unit.
Upstream

Production & wellsite applications

For production fluids and produced water where black powder and fine contamination are damaging surface equipment:

  • Protecting pumps, valves, seals and chokes from abrasive wear
  • Produced water handling ahead of treatment or disposal
  • EOR support systems — thermal, gas injection and chemical flooding
Midstream

Processing, pipelines & terminals

For hydrocarbon fluid and gas systems moving product between production and refining:

  • Gas processing and pipeline facilities
  • Intercepting black powder before it reaches compressors and rotating equipment
  • Protecting product quality downstream of transport
Downstream

Refining & upgrading applications

For refineries, upgraders and plant process systems where contamination loads are continuous:

  • Upstream protection for filter systems and heat exchangers
  • Rotating equipment protection in process service
  • Used oil and process fluid cleanup for reuse
Beyond oil & gas

Water, hydraulics & power generation

The same contamination problem appears wherever fine particles circulate in a working fluid. MagStream applications also include:

  • Water and produced-water systems
  • Hydraulic and lube oil circuits
  • Power generation and other industrial fluids

Confirmed for each duty before supply.

Fluid and contamination, flow rate, pressure and temperature, seal materials and fluid compatibility, and any applicable approvals — checked once, before supply. TrueCan also engineers custom systems and maintenance plans.

Quick check · 30 seconds

Could magnetic filtration help your operation?

Tick what you're seeing on site — the result points you to the next step.

What kind of system?
What are you seeing? Tick all that apply
—

Tick what you're seeing

Your next step will appear here.

Evidence

What the technology has done — manufacturer case studies

Source: Eclipse Magnetics manufacturer case studies — Eclipse is TrueCan's manufacturer and supplier. These are Eclipse installations, not TrueCan installations, and results depend on each application's duty.

Steel rolling & pickling

Steelscape — Kalama, USA

≈12,000 kg extracted per month

Application: Steel rolling and pickling line.

Problem: Ferrous particles smaller than 50 microns kept circulating and caused imperfections in the steel surface. Smaller-micron filters were trialled but blocked very quickly under the contamination load.

Equipment: Eclipse Automag AM6 Skid, fitted before the existing Oberlin filter.

Measured result: Approximately 12,000 kg (26,400 lbs) of ferrous oxide extracted each month, and reject rates fell to virtually zero.

Read the Eclipse case study →
Gear grinding & honing

Scania — transmission gears

Oil life increased 30%

Application: Grinding and honing of transmission steel parts, lubricating oil circulated at 10–12 bar and 380–400 litres per minute.

Problem: Magnetic rollers only removed particles of 0.1 mm and above; everything smaller kept circulating, wearing grinding tools and raising reject rates.

Equipment: Eclipse Filtramag FM2.5, fitted as a secondary filter after the magnetic roller.

Measured result: Tool changes and product rejects caused by ferrous contamination reduced to virtually zero, and oil lifespan increased by 30%.

Read the Eclipse case study →
Camshaft grinding

Schaudt Mikrosa — automotive OEM supplier

Downtime costs cut by at least 50%

Application: CNC camshaft grinding for the automotive industry.

Problem: The paper filter could only remove particles down to 20 microns; finer ferrous particles built up around the grinding wheel and camshaft, damaging wheels and surface finish.

Equipment: Eclipse Filtramag FM2.5, fitted ahead of the paper band filtration unit.

Measured result: Maintenance and downtime costs reduced by at least 50%, grinding wheel life increased 25–30%, and product rejections fell 10–15%.

Read the Eclipse case study →

These are industrial fluid duties, published by the manufacturer. For an oil & gas duty, the relevant measure is your own: a pilot produces measured results from your fluid, under your operating conditions. Eclipse's full technology overview is in its magnetic filtration brochure (PDF).

Low-risk first step

Don't buy a plant-wide system. Start with one pilot.

Prove it on one problem system, measure what changes, then decide.

1

Baseline first

Baseline testing and performance measurements agreed during the technical review, taken before anything is installed.

2

One system

One correctly sized unit on the circuit that costs you the most — not a site-wide commitment.

3

Open it and measure

Photograph and weigh what was captured, repeat the fluid testing, and compare against the baseline.

4

Decide with data

Roll it out, add a maintenance plan, or walk away — based on your measured results.

One system onlyDecide with your own data

FAQ · The technical detail

Questions operators ask, answered precisely

Straight answers on capture, sizing and suitability.

Is black powder only magnetic material?

No. Part of it is ferrous and magnetic — iron oxide, magnetite and iron sulfide. Part is non-ferrous and non-magnetic — silica, sand, salts, scale and other fines. The mix differs between applications.

If a particle isn't magnetic, how can it be captured?

Two effects are at work. Via the corral effect, ferrous particles held on the magnets form a matrix that physically traps non-ferrous particles travelling with them. And through static charge, as particles collide in the flow, non-magnetic particles can be attracted to and retained with the captured material. That is how non-magnetic contamination ends up in what is cleaned off a unit. For its part, Eclipse Magnetics' product literature describes its filters as capable of removing abrasives and non-magnetic material by means of heterocoagulation — particles attaching to captured ferrous material. How much non-magnetic capture occurs in a given duty depends on the fluid and contamination; it is not a universal removal rate.

What does "sub-micron capture" actually mean?

It describes a capability documented by the manufacturer: Eclipse Magnetics' filtration brochure states its systems remove ferrous particles including submicron particles, and its Micromag product literature states the high-intensity core can attract even a sub-micron sized particle — below one micron. A capability is not the same as a guaranteed removal efficiency. How much contamination is removed in one pass through a real system depends on particle size distribution, fluid, flow rate and operating conditions, and is best established by measurement — for example, fluid testing before and during a pilot.

Why don't finer conventional filters just solve this?

Conventional barrier filters catch what is larger than their pores. Much black powder is smaller than that, so it passes through — and making the filter finer makes it plug faster, raises pressure drop, and turns filtration into a recurring cost for cartridges, labour and disposal. Magnetic filtration captures fine ferrous contamination that may pass through existing filtration, and fitted ahead of it, reduces the load on downstream filters so their media lasts longer.

How would I know if my system has black powder?

Common signs are black sludge or dark particles in strainers and filters, frequent change-outs, unexplained pump, valve or seal wear, plugged exchangers, and downtime that traces back to fouling or blockages. The only way to know what is actually in your fluid is to inspect what your filters are catching, or to test the fluid — which is step one of a pilot.

What decides whether a unit suits my system?

Suitability is confirmed against the checklist under Products before anything is supplied. If it doesn't fit, we'll say so.

What happens to the contamination once it's captured?

It stays on the rods until planned maintenance, when they're lifted out, cleaned and returned to service — no disposable cartridges to replace.

Ready when you are

Get a clear answer for your system

Tell us what you're seeing on one system, plus any duty details you know — you'll get a straight assessment.

An honest fit assessmentJudged on your system and its duty.
Sized to your operationNot a generic catalogue pick.
A pilot you controlMeasured results, then your decision.
Email TrueCan[email protected]Send the same details as the form, any time.
Call TrueCan1.250.883.0499Prefer to talk it through? Call us.
Onlinetruecantech.comTrueCan Industrial Technologies Inc. · Global Distribution

Tell us about your system

Share what you know; technical details are optional.

✓ Thank you — your request has been submitted

Your technical review request has been submitted through the website form. We'll reply to the email address you gave. If you don't hear back within two business days, please email [email protected] or call 1.250.883.0499 to confirm we've received it.

Submits directly through this website — no email app needed. No pressure, no obligation.